'67 Dodge Dart leaf spring Relocation - YouTube
A video showing the leaf spring relocation on my '67 Dart GT, along with ideas, things to avoid etc. Be sure to check out the tech pages at bigblockdart.com where I got most of the information. ... View Video
ART-102 Installation Instructions - Auto Rust
ART-102 Installation Instructions 1987-96 Jeep Wrangler Front Frame, Shackle, & Steering Box Mount Kit weld. b) “Mig” (wire fed) welding produces a very sound weld. We suggest a 220 volt this will make it easier to lower the leaf spring. ... Read Full Source
Catalog Volume 5 - Old Dog Street Rods - Your Midwest Street ...
1933-34 Complete IFS with Air Spring Option Part # Details Starting At TCI 103-1285-00 Plain Package $12,058.00 TCI 103-1285-01 Chrome Package $13,313.00 TCI 103-1285-02 Chrome/Stainless Package $13,558.00 1933-34 Complete Dropped Axle Chassis Dropped Axle Front Suspension include: Tube axle, mono-leaf spring, equal length parallel ... Fetch Content
3-link Rear Suspension Kit - Trail-gear.com
Tack weld the plates to frame to insure proper ˜tment, then fully weld plates to frame. step 5a - INSTALL FRAME BOX PLATES (TACOMA ONLY) Prep frame for frame box plate by grinding all mating surfaces 3” 3” step 6 - AXLE PREP With the perches removed, Place the axle on jack stands and set your desired pinion angle. If this is to be driven ... Return Document
Installation Instructions 1948-1952 FORD F-1 PICKUP ...
MEASURE TWICE, WELD ONCE! 1. Start by supporting the truck on 4 jack stands. The truck should be sitting on approximately the same angle as it does on the ground, or slightly lower in front. 2. Remove all the old front suspension components, including the leaf springs and the engine mounting rails. Also remove the spring perches from the frame ... Retrieve Content
Sidekick / Tracker Solid Axle Suspension 2 Door Installation ...
18. Weld brackets in place. The upper bracket should only be skip welded. Rear Axle ** Requires 1986 to 1995 Toyota pick-up complete rear end with 2 3/8” wide spring perches. The factory e-brake cable bracket and proportioning valve rod bracket could be removed. ** DO NOT remove the factory leaf spring perches or the brake hose / line tabs. 19. ... Read Content
HOME A L C ON Total Control Products O T P R O D UCTSTROL
Total Control Products T O T A L C O N T R O L P R O D U C S 8883880239 33 TotalControlProductscom N E W N E W N E W N E W N E W N E W U-Bolt Sets Leaf Springs VariShock Bolt-Ins Leaf Spring FAB9s Leaf Spring Plates Anti-Roll Bar Shackle Set Front Bushing Set Leaf Spring Suspension - Complete Systems Leaf Spring Suspension - Individual ... Return Doc
TRAILER BREAKTHROUGH - Ucfamerica.com
TRAILER BREAKTHROUGH T leaf-spring systems and are gaining in popularity, especially with up-scale boat-trailer builders. There are no hangers to position and weld, no bushings to install and no extra linkage to bolt in place. ... Read Here
Tacoma Rear Lift Kit - Low Range Off Road Blog
Remove factory perches from housing and grind clean. step 30 step 31 step 31 continued Install new perches without welding , u-bolts, and plates to leaf spring and housing and tighten to a snug fit. Center pin to center pin should be 39 1/2”. step 32 Place rear axle on jack stands with weight of vehicle on suspension. ... Read Here
NARROW LEAF SPRINGS INSTALLATION INSTRUCTIONS
Perches to line up with the springs. Narrow the shock plates accordingly. Or, if you are using with standard location perches, use the offset pin adaptors. However, you will only get a 3/8” offset of the spring. They sandwich between the housing perch and the leaf spring. The spring center ... Access Full Source
2686 Highway 92 - Oskaloosa, IA 52577 Phone: 641.673.0468 ...
The weld and cut Measure back 24” and cut off the tailpipe . 1. Jack up the rear of the frame so that most of the tension is off the leaf springs. Next, remove the front leaf spring perches, leaf springs and the overload pads. Use a sharp chisel and large hammer or air hammer to break off ... Document Viewer
Installation Instructions Part# 87400 2007+ Tundra Rear ...
Set the new spring perches on top of the leaf springs with the leaf spring center pin going through the corresponding hole in the perch. Tack weld in place and remove the shocks, then weld both lower shock mounts, let them cool and paint. ... Doc Viewer
You Will Need - Danchuk.com
Danchuk # 10235 Leaf Spring Relocation Kit spring perches that come with the pocket kit that you will use if you are re-using your stock rear, but we do outline the procedure according to the installation weld material smooth. 2. Locate the 1-1/4” hole on the frame where the front of ... Access Full Source
Classicchevy.com
Leaf spring-eye fits into the new forward spring pocket. The rear spring-eye attaches to the new shackle and bushings weld the spring perches solid to the rear end housing. 29 29c Photo #29a, 29b & 29c: Set the rear end back onto the leaf springs. Using the stock U-bolts, ... Read Document
Making Spring Perches & MailTime - YouTube
Making Spring Perches & MailTime Matthew Cherrington How to Fix Broken or Cracked Plastic or Weld Plastic Auto Coil And Leaf Spring Classic Car Tips and Tricks Do and Don't Episode ... View Video
INSTALLATION INSTRUCTIONS INST-11-20-010A CJ Ull Width Ront ...
INSTALLATION INSTRUCTIONS INST-11-20-010A CJ ull Width ront The kit is designed to fit axles with leaf spring perches that measure 31-1/4” center-to-center. This includes most Chevy, Ford, full-size Jeep and weld into place, using 1” beads alternating with 1” gaps. ... Retrieve Here
Dana 44 Perch Welding - YouTube
Welding on the perches for my Dana 44. Its going in my XJ with 4.10 gears the front D30 is next with an ARB :) ... View Video
Typical Tandem Installation - Timbren Industries
Aeon® Spring Fasteners to mount Frame Bracket to Frame (Not supplied) Inboard Do not weld U-bolts Procedure: factory pre-loaded. Typical Tandem Installation. Page 2 Installation Instructions Procedure: (Cont.) 5. To align axle, l 6. Once axles are aligned, torque U-bolts to 70-75 ft-lbs ... View This Document
SSP-TSRM Suzuki Samurai To Toyota REAR Spring Swap Kit, With ...
Suzuki Samurai to Toyota Rear Spring Swap Kit, with Missing Link Shackles (SKU#SSP-TSRM) Lift up on the leaf spring and remove the outer shackle plate and bolts. Drilling the Spring Perches Step 26 ... Return Doc
1979 And Prior FORD 1/2-TON PICKUP AND BRONCO With Solid ...
Cut/weld process. Sleeving link shanks will add strength and make for a “cleaner” job. WARNING: The spring perches, where the leaf springs or blocks seat on the axle, are NOTE: The spring perches are prone to collapse or warp where the leaf springs or blocks seat on the axle ... Doc Retrieval
No comments:
Post a Comment